Home        Installing Scenery   


Creating Airport Scenery : Start Ramps

Return

Setting start ramps is a simple affair.  You can specify the aircraft size, airline and parking position for any ramp and also set the conditions associated with it.  Getting this wrong could place a jumbo jet in a shoe box!

Where AI aircraft are active, X-Plane will place aircraft in the air and on the ground at appropriate ramps.  These aircraft may also taxi out and take off, using existing taxiways and runways.

Ramp Names - This will appear on the X-Plane flight configuration screen under Customize Location.  Ramps on the Apron (pan) are usually numbered 1, 2, 3, etc  There may also be Loading Gates or parking on a Grass Apron, by or in the Hangar, or at Dispersal.  Name the gates, ramps and parking appropriately to their ground locations.  

A few basics - ramps sizes are important.  There must be enough room to accomodate the aircraft and allow it to move out onto the taxiways.  It other parking possitions are a potential obstruction, it may be best not to set them as ramps, but just represent them visually in the scenery.

Aircraft size A Light aircraft.  e.g. Cessna 127, Beechcraft Baron
B Short to medium haul.  e.g.  Boeing 737, DH Dash 8
C Small long haul.  e.g. Bombarier Global 6000
D Large long haul.  e,g, Airbus A310
E Big metal.  Boeing 777
F Very big metal.  Airbus A380-800

 Ramp Start

Ramp Type Misc Default setting - not normally used
Gate Gives pushback equipment as standard for nosewheel jets
Tie Down No additional equipment added
Hangar Cold Start ramp

Equipment type- you can select multiple types for the ramp for Prop; Turboprop; Jet; Heavy Jet; Helicoptors or Fighters.  Common sense dictates that a ramp for a light aircraft would not be set for heavy jets.  An appropriate selection of equipment will be added to the ramp to suit the aircraft type if Gate has been selected.

Ramp Operations- can be None; General Aviation; Airline; Cargo or Military.  This setting helps AI to place appropriate types on free ramps.  If in doubt about the ramp use, select None.

Airlines - all airline operators have a 3 letter code that identifies them.  Air France is AFR, Hawaiian Airlines is HAL.  You can look up the 3 letter identifier on the internet and select specific airlined for ramp permissions.  (Example colour schemed must be resident in the sym aircraft for them to show).  Any number of codes can be used with a space between each.  Select airline codes for operators that would use your airport.

e.g.         BAW BAT XMS SHT  ( this will give all of the British Airways companies for a set ramp )

You can open X-Plane 11 and WED together and toggle between them.  if you alter WED, then save and export scenery pack,  you can toggle to X-Plane and - using the developer tag, reload scenery - to see how the changes have worked.

Reload scenery and see which airliners populate free ramps.  Change the time of day and repeat the reload.

Ramp Markings.  The markings on any ramp are usually a taxiline, with a cross bar or a terminal bar in yellow.  However, this will vary from airport to airport.  There may be hatched areas to delineate operational zones or restricted zones around an aircraft.  There may be coloured squares or rectangles with numbers in, to mark the ramp, or nosewheel position,  There may be grunge on the ground around the ramp.  Google earth and local photographs can be very helpful in setting the correct markings.

This example of ramps is not typical.  The position and type of taxiway, ramp and vehicle/pedestrian zones will be different for each airport.

          

Top Tips

If you want a ramp to be always clear of aircraft, do not use the ramp tool to define the ramp.  Just add the ground markings.  If the empty ramp is in a sequence, its number will be missing from the customize list on the location screen.

Place and aircraft at the ramp position in WED to see how it fits, before adding the ramp markings.

Check each ramp position in X-Plane 11 to make sure that the aircraft is positioned correctly.